Home News

Design of LED driver for high power LED bulb replacement application

Certification
China Shenzhen RIYUEGUANGHUA Technology Co., Limited certification
China Shenzhen RIYUEGUANGHUA Technology Co., Limited certification
I'm Online Chat Now
Company News
Design of LED driver for high power LED bulb replacement application

Introduction: This paper introduces a reference design of LED driver for high power LED bulb replacement application. The driver can provide the required power for the LED replacement lamp of 100 W A19 incandescent bulb. It is a non isolated, high efficiency (93%) and high power factor (PF) led driver. The driver can fit into the A19 bulb exactly. It not only meets the en61000-3-2 C (d) standard, but also easily meets the thd limit requirements. The power factor (PF) value exceeds 0.95, so it is suitable for both commercial and consumer applications.

 

According to estimates, China's lighting power consumption accounts for about 12% of the total social power consumption. If all the incandescent lamps in use are replaced with energy-saving lamps or LED lights, the annual power saving can be 48 billion kwh, equivalent to 48 million tons of carbon dioxide emissions reduction. It can be seen that the market potential of LED lighting is huge. The national development and Reform Commission issued the roadmap of China's phase out of incandescent lamps, which indirectly promoted the development of LED lighting market.

 

Market potential of LED driver for 100W A19 incandescent bulb replacement application

 

Andrew Smith, product marketing manager of power integrations, said: "all countries begin with the elimination of high-power 100W incandescent lamps, followed by low-power 75W incandescent lamps. The EU eliminated 100W incandescent lamps in 2010, while the United States and China began to eliminate them in 2012. Therefore, there is a very strong market demand for high-power LED which can replace 100W incandescent lamp. "

 

Now 100 W incandescent lamp replacement led generally need to use PAR38, the use of A19 specification LED has not yet appeared. Now PI has launched the industry's first LED driver design der-322 for 100 W A19 incandescent bulb replacement application, which can provide the required power for 100 W A19 incandescent bulb LED replacement lamp, which is the industry's first such design. The introduction of PI high-power LED drive design will greatly promote the replacement of 100W incandescent high-power led to enter the market quickly.

 

The der-322 driver can be put into the A19 bulb exactly, which not only meets the en61000-3-2 C (d) standard, but also easily meets the thd limit. Its power factor (PF) value exceeds 0.95, so it is suitable for both commercial and consumer applications. Due to the integration of PFC and CC conversion in the same switch level, the number of components in the design is very small, which helps to realize the miniaturization of the drive, reduce its cost and enhance reliability. In addition, it uses ceramic capacitor elements, which can save the short life of large capacity input electrolytic capacitor, which is helpful for the improvement of product life.

 

The applicability of der-322 is also outstanding. It is not only suitable for the LED replacement lamp driver of A19 incandescent bulb, but also can be configured as the LED replacement lamp driver of T8 lamp tube. Therefore, it has a strong attraction for both high-end LED lighting designers and low-cost designers who are committed to optimizing the retail category. The reference design can be modified to support SCR dimming.

 

Of course, objectively speaking, there are still many technical problems to be solved for high-power LED at present. In addition to the LED driving part that Pi gives priority to, other related manufacturers need to work together to produce final products, such as heat dissipation, high-power LED particles, etc.

 

Andrew Smith pointed out: "as long as there is a clear market demand, the corresponding manufacturers will increase investment in specific technologies. I think the high-power LED terminal products that can replace 100W incandescent lamps by the end of 2012 are expected to appear. " With the corresponding products, driven by the policies of various governments, we believe that high power LED will have good development potential

 

This design is made of der-305 PCB, and maximizes the area of lnk460vg device radiator.

Pub Time : 2019-12-19 18:00:52 >> News list
Contact Details
Shenzhen RIYUEGUANGHUA Technology Co., Limited

Contact Person: Mr. Hugh Hu

Tel: +86 136 8680 7553

Send your inquiry directly to us (0 / 3000)